Introducing the dB DAWG by Ignition Racing.  An exhaust insert that can reduce up to 10db in exhaust sound with no noticeable power loss.  The dB DAWG is track tested in real race environments.

Track Owners can stock these low cost exhaust inserts to have available track side.

Riders can install the dB DAWG in minutes and ride at their favorite track or riding area while helping reduce exhaust noise with no noticeable power loss.  Don't be turned down at the track because your bike failed the sound test, install the dB DAWG and RIDE!

How does the dB Dawg work?
Air will take the path of least resistance, but sound needs to hit something to cancel it out.  We designed the dB Dawg insert in such a way (with the flat end and angled corners) that when the sound waves hit the end of the insert some of them cancel out and others bounce back into the packing of the muffler which are also cancelled out - this is also why you may need to replace the packing more frequently. The length of the shaft and the outlet hole are all exact calculations for maximum noise reduction and minimum power loss. Altering the insert in anyway will render it less if not totally ineffective.

Tuning with the dB Dawg
Installing the dB Dawg on some bikes tend to run a little rich which may cause a slight loss of power on the low end. Most riders leave the tuning alone and are happy how the bike runs.  While some riders are dropping the needle one position and making some fuel screw adjustments to bring the performance up.

Measuring Tips
Measure the inside diameter of the exhaust outlet for external fit.
Measure for a straight length of 2-1/2" minimum to support insert portion.

Installation Tips
- Install and run down allen screws with fingers as far as possible prior to installation.
- Do not over tighten allen set screws. Over tightening set screws can deform the  internal tube of silencer.
- If you are going to run the dB Dawg permanently some riders are using high temp silicone around the base to provide an enhanced seal and to add extra mounting support.

PHONE ORDERS AND QUESTIONS CALL TOLL FREE: 888-507-3648

dB DAWG FEATURES

• Easy to install

• All necessary parts included

• Reduces noise levels up to 10db with just an insert

• Average noise drop is 4-6db

• No noticeable power loss

• No exhaust modification required

• Non-permanent

• Easy to remove

• Low cost

• Allen wrench included

• BUY NOW

dB DAWG 8001

dB DAWG - Silencer Insert - External Fit
Part # 8001

• Exhaust Outlets from 1.31" to 1.50"

• Reduces noise levels up to 10dB's with just an insert

• No exhaust modifications needed

• BUY $41.95

dB DAWG 8002

dB DAWG - Silencer Insert - External Fit
Part # 8002

• Exhaust Outlets from 1.50" to 1.75"

• Reduces noise levels up to 10dB's with just an insert

• No exhaust modifications needed

• BUY $41.95

dB DAWG 8003

dB DAWG - Silencer Insert - External Fit
Part # 8003

• Exhaust Outlets from 1.75" to 2.00"

• Reduces noise levels up to 10dB's with just an insert

• No exhaust modifications needed

• BUY $41.95

dB DAWG 8010B

dB DAWG - 4 Stroke Silencer Insert - External Fit
Part #8010B
Fits Yamaha YZ450F 2007

• Fits Yamaha YZ450F 2007

• Exhaust Outlets From 1-1/8" to 1-3/16"

• Reduces noise levels up to 10dB's with just an insert

• BUY $58.95

dB DAWG 8010R

dB DAWG - 4 Stroke Silencer Insert - External Fit
Part #8010R
Fits Honda CRF250 2006-2007

• Fits Honda CRF250 2006-2007

• New Shorter Set Screws! (not shown)

• Exhaust Outlets From 1-3/16" to 1.31"

• Reduces noise levels up to 10dB's with just an insert

• BUY $58.95

dB DAWG 8100

dB DAWG - 4 Stroke Silencer Insert Internal
Fits Pro Circuit Ti-4 Silencer
Part #8100

• Fits Pro Circuit Ti-4 Silencer

• Fits inside end cap

• Insert From D=1-9/16" to 1-3/4"

• Insert L = 2-1/2"

• Machined End Max D = 1-3/4"

• Machined End L = 7/16"

• Can also be used as an universal external fit

• Reduces noise levels up to 10dB's with just an insert

• BUY $58.95

dB DAWG 8102

dB DAWG - 4 Stroke Silencer Insert Internal
Fits DRD Silencer
Part #8102

• Fits DRD Silencer

• Fits inside end cap

• Also fits external universal applications

• From D=1-3/4" to 2" L=2-3/4"

• Reduces noise levels up to 10dB's with just an insert

• BUY $58.95

dB DAWG 8031

dB DAWG - 4 Stroke Silencer Insert Internal
Fits 07' KTM SX New Style Silencer
Part #8031

• Fits 07' KTM SX New Style Silencer

• Fits inside end cap

• Insert > From D=1-11/16", L=2-1/2" (black area in above image)

• Machined end > D=1-9/16" L=7/16"

• Fits from D=1-11/16" to 2" internal and external

• Can be used as a slip-in for a stealth look!

• Reduces noise levels up to 10dB's with just an insert

• BUY $58.95

dB DAWG 8032

dB DAWG - 4 Stroke Silencer Insert Internal
Fits 2002-2006' KTM SX Stock Oval Muffler Only
Part #8032

• Fits 2002-2006' KTM SX Stock Oval Muffler Only

• Non-Spark Arrested - Tapered Perforated Internal Tubes Only

• Fits inside end cap

• Insert > From D=1-1/2", L=2-1/2" (black area in above image)

• Machined end > D=1-1/2" L=7/16"

• Fits from D=1-1/2" to 1-3/4" internal

• Can be used as a slip-in for a stealth look!

• Reduces noise levels up to 10dB's with just an insert

• BUY $58.95

Questions?  Call 888-507-3648 or info@dirtwerkz.com